Monitor Cleanings

image

>Get maximum efficiency and economy from your Monitor Heating System>

Monitor 40, 41, 441, 2400- Recommended to be done once every three years:

Inspecting your system, Full Monitor Cleaning. Unit to be set to factory specs.
Check bearings, Clean all fans, Clean pwb board/check
wire connections, Clean cabinet, Clean grill, Clean drip pan, Clean strainer,
Check for debris, Check flame detective plug, Air flow check with special
Manometer guages, Set air to fuel ratio, Necessary tools, material and labor to
perform described job. All taxes included.

Replacement of all itemized parts listed below:

New Combustion Burner Ring
New Front Chamber gasket
New filter cartridge at tankFlame detective plug packingDamper o-ringLabor/Service

$499.00

*Combustion Blower motor bearing replacement, add $125.00 per heater. Reg. charge is $225.00 *More than One? Deduct $10.00 per heater at same location.

*Pressure testing for fumes, add $35.00

*High Temperature Exhaust O-rings, add $7.00 each for extension kits. *Any unforeseen items, potential problems or recommendations will be addressed and discussed with an
estimate of additional cost.

*Outside tank? Add K-1 PLUS for $16.00 per 250 gallons for moisture/water dispersment.

*Heaters with no history of maintainance must have damper o-ring changed. An addtional $15.00 will be added.

Monitor 40, 41, 441, 2400 - Recommended to be done once every six years:

Inspecting your system, Full Monitor Cleaning. Unit to be set to factory specs.
Check bearings, Clean all fans, Clean pwb board/check
wire connections, Clean cabinet, Clean grill, Clean drip pan, Clean strainer,
Check for debris, Check flame detective plug, Air flow check with special
Manometer guages, Set air to fuel ratio, Necessary tools, material and labor to
perform described job. All taxes included.

Replacement of all itemized parts listed below:

New Combustion Burner Pot Assembly
New Combustion Burner Ring
New Front Chamber gasket
New filter cartridge at tank
Flame detective plug packing
Damper o-ring
Small and Large O-ring at exhaust flue
O-gasket for ignitor
Combustion chamber gasket at Base
Heater Cover packing
Truck Supplies
Labor/Service

$799.00

Greetings,

Now that warmer weather is finally here, many of you have stopped using your heaters for the summer months and now would be an excellent time to have the routine tri-annual maintenance performed.

Monitor Heaters do require periodic maintenance at about three years of service. Occasionally, there are problems that arise after three years.

We will thoroughly clean your heater or hot water heater and inspect/check for any potential problems such as water in your outside tank, noisy motors, oil lines, installation, etc. Also if applicable, we will advise you of any new state code updates. Some of which, have been recently made into effect and inform you of what any additional costs could be to repair or update a condition.

We encourage you if you have any intentions of having your unit serviced this spring/summer to act soon!

Please call today for more information and consider the benefits while allowing us to serve you more efficiently during our off peak season instead of waiting for the fall rush. Complete Financing is available through MasterCard, Visa, and Discover or with one of our Home Source Plans.

From plumbing, heating and oil services, we look forward to bringing new ideas, innovations and new technology to help save you money.

Richard E. Burke, Jr.
Perfect Plumbing and Heating, Inc.
Maximum Energy

 

image

>Get maximum efficiency and economy from your Monitor Heating System>

Monitor 21, 22, 422, 2200 - Recommended to be done once every three years:

Inspecting your system, Full Monitor Cleaning. Unit to be set to factory specs.
Check bearings, Clean all fans, Clean pwb board/check
wire connections, Clean cabinet, Clean grill, Clean drip pan, Clean strainer,
Check for debris, Check flame detective plug, Air flow check with special
Manometer guages, Set air to fuel ratio, Necessary tools, material and labor to
perform described job. All taxes included.

Replacement of all itemized parts listed below:

New Combustion Burner Pot Assembly
New Combustion Burner Ring
New Front Chamber gasket
New filter cartridge at tank
Flame detective plug packing
Damper o-ring
Small and Large O-ring at exhaust flue
O-gasket for ignitor
Combustion chamber gasket at Base
Heater Cover packing
Truck Supplies
Labor/Service

$599.00

*Combustion Blower motor replacement, add $225.00 per heater. Reg. charge is $325.00

*More than One? Deduct $10.00 per heater at same location.

*Pressure testing for fumes, add $35.00

*High Temperature Exhaust O-rings, add $5.00 each for extension kits.

*Any unforeseen items, potential problems or recommendations will be addressed and discussed with an
estimate of additional cost.

*Outside tank? Add K-1 PLUS for $16.00 per 250 gallons for moisture/water dispersment.

*Suction case cover, add $85.00

** New heat x changer replacement for 40, 41, 441 or 2400 add $450.00 No heat x changer for 21, 22, 422, 2200 are not available.